Home > Kodu ja sisustus > Uksekellad > Alecto Uksekellad > Alecto ADB-19 Uksekell

Kasutusjuhend Alecto ADB-19 Uksekell

Kas vajate oma Alecto ADB-19 Uksekell’i jaoks kasutusjuhendit? Allpool saate vaadata ja tasuta alla laadida eestikeelset PDF-juhendit. Sellel tootel on praegu 0 korduma kippuvaid küsimusi, 0 kommentaare ja sellel on 0 hääli. Kui see pole teie soovitud juhend, võtke meiega ühendust.

Kas teie toode on defektne ja kasutusjuhendist pole abi? Tasuta remonditeenused: Repair Café.

Kasutusjuhend

ADB-19 Installation

Outdoor-unit:

Indoor-unit:

Important Note:

● If you do not plan to use the device for a long time, such as at a vacation, please remove the

battery from Transmitter, then put them in a safe place.

● Improperly using a battery may cause it to leak and damage nearby items, and can create the

risk of fire and personal injury. Batteries should not be left in an area where the children can

reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practices.

Transmitter Installation:

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).

Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)

and place the battery. Please be well noted with the correct battery polarity. To replace a new

battery, operate in the same way.

Press lightly the battery

holder at side

CR2032 3V Lithium Battery

Important Note:

● If you do not plan to use the device for a long time, such as at a vacation, please remove the

battery from Transmitter, then put them in a safe place.

● Improperly using a battery may cause it to leak and damage nearby items, and can create the

risk of fire and personal injury. Batteries should not be left in an area where the children can

reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practices.

Transmitter Installation:

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).

Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)

and place the battery. Please be well noted with the correct battery polarity. To replace a new

battery, operate in the same way.

Press lightly the battery

holder at side

CR2032 3V Lithium Battery

Connecting:

Important Note:

● If you do not plan to use the device for a long time, such as at a vacation, please remove the

battery from Transmitter, then put them in a safe place.

● Improperly using a battery may cause it to leak and damage nearby items, and can create the

risk of fire and personal injury. Batteries should not be left in an area where the children can

reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practices.

Transmitter Installation:

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).

Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)

and place the battery. Please be well noted with the correct battery polarity. To replace a new

battery, operate in the same way.

Press lightly the battery

holder at side

CR2032 3V Lithium Battery

Accessories List:

● 1 x Receiver ● 1 x Transmitter

● 1 x User Manual ● 1 x Double-sided adhesive

● 1 x 3 volts CR2032 battery for transmitter

Technical Specification:

● Frequency: 433.92MHz+100KHz

● Modulation Type: ASK

● Ring Volume:＞85dB(within 0.5m)

● Channel space: 1 million sets of auto-learning codes

● Receiver bandwidth: ±90KHz

● Reception Sensitivity:＞-105dBm

● Transmitter Power:＜10mW

● Power consumption(Receiver): standby:＜0.3W

● Power consumption(Transmitter): standby:＜5uA working:＜10mA

● Power Supply(Receiver): AC110-240V

● Power Supply(Transmitter): DC 3V (1x CR2032)

● Operating Range:＞150m (in the open air)

Names for Parts:

Instruction Manual

Auto-leaning Code Wireless Door Chime

Model No.: QH-861AK

VOL

MODE

CODE

Important Note:

● If you do not plan to use the device for a long time, such as at a vacation, please remove the

battery from Transmitter, then put them in a safe place.

● Improperly using a battery may cause it to leak and damage nearby items, and can create the

risk of fire and personal injury. Batteries should not be left in an area where the children can

reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practices.

Transmitter Installation:

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).

Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)

and place the battery. Please be well noted with the correct battery polarity. To replace a new

battery, operate in the same way.

Press lightly the battery

holder at side

CR2032 3V Lithium Battery

1x1x

<10 sec.

Important Note:

● If you do not plan to use the device for a long time, such as at a vacation, please remove the

battery from Transmitter, then put them in a safe place.

● Improperly using a battery may cause it to leak and damage nearby items, and can create the

risk of fire and personal injury. Batteries should not be left in an area where the children can

reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practices.

Transmitter Installation:

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).

Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)

and place the battery. Please be well noted with the correct battery polarity. To replace a new

battery, operate in the same way.

Press lightly the battery

holder at side

CR2032 3V Lithium Battery

Important Note:

● If you do not plan to use the device for a long time, such as at a vacation, please remove the

battery from Transmitter, then put them in a safe place.

● Improperly using a battery may cause it to leak and damage nearby items, and can create the

risk of fire and personal injury. Batteries should not be left in an area where the children can

reach them as they may pose a chocking hazard.

● Recycle used batteries following environmental protection practices.

Transmitter Installation:

● Stick the Transmitter on the wall or the door with

double-sided adhesive tape.

Receiver Installation:

● Plug the Receiver into any socket of AC110~240V power.

Battery Installation (Transmitter):

Transmitter uses a 3V CR2032 battery (included).

Open the Transmitter (by pushing in the interface located at the bottom with a flat screw driver)

and place the battery. Please be well noted with the correct battery polarity. To replace a new

battery, operate in the same way.

Press lightly the battery

holder at side

CR2032 3V Lithium Battery

Accessories List:

● 1 x Receiver ● 1 x Transmitter

● 1 x User Manual ● 1 x Double-sided adhesive

● 1 x 3 volts CR2032 battery for transmitter

Technical Specification:

● Frequency: 433.92MHz+100KHz

● Modulation Type: ASK

● Ring Volume:＞85dB(within 0.5m)

● Channel space: 1 million sets of auto-learning codes

● Receiver bandwidth: ±90KHz

● Reception Sensitivity:＞-105dBm

● Transmitter Power:＜10mW

● Power consumption(Receiver): standby:＜0.3W

● Power consumption(Transmitter): standby:＜5uA working:＜10mA

● Power Supply(Receiver): AC110-240V

● Power Supply(Transmitter): DC 3V (1x CR2032)

● Operating Range:＞150m (in the open air)

Names for Parts:

Instruction Manual

Auto-leaning Code Wireless Door Chime

Model No.: QH-861AK

VOL

MODE

CODE

Hinnang

Andke meile teada, mida arvate tootest Alecto ADB-19 Uksekell, jättes selle kohta hinnangu. Kas soovite jagada oma kogemusi selle tootega või esitada küsimuse? Jätke kommentaar lehe alumises servas.

Kas olete teenusega Alecto ADB-19 Uksekell rahul?
Jah Nr

Olge esimene, kes seda toodet hindab

0 häält

Liituge selle toote teemalise vestlusega

Siin saate jagada, mida arvate Alecto ADB-19 Uksekell kohta. Kui teil on küsimusi, lugege esmalt hoolikalt kasutusjuhendit. Kasutusjuhendit saab taotleda kasutades meie kontaktivormi.

Lisateavet selle juhendi kohta

Mõistame, et on tore, kui teil on teie Alecto ADB-19 Uksekell jaoks paberjuhend. Juhendi saate alati meie veebisaidilt alla laadida ja ise printida. Kui soovite originaaljuhendit, soovitame võtta ühendust ettevõttega Alecto. Nad võivad anda originaaljuhendi. Kas otsite oma Alecto ADB-19 Uksekell kasutusjuhendit mõnes muus keeles? Valige meie kodulehelt oma eelistatud keel ja otsige mudelinumbrit, et näha, kas see on meil saadaval.