Kasutusjuhend Ryobi EAG750RS Nurklihvija

Kasutusjuhend

2

English

GB

FR DE ES IT NL PT DK SE FI NO RU PL CZ HU RO LV LT EE HR SI SK GR TR

FURTHER SAFETY INSTRUCTIONS FOR ALL OPERA-

TIONS

Kickback and related warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other accessory.

Pinching or snagging causes rapid stalling of the rotating

accessory which in turn causes the uncontrolled power tool

to be forced in the direction opposite of the accessory’s

rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched

by the workpiece, the edge of the wheel that is entering

into the pinch point can dig into the surface of the material

causing the wheel to climb out or kick out. The wheel may

either jump toward or away from the operator, depending

on direction of the wheel’s movement at the point of

pinching. Abrasive wheels may also break under these

conditions.

Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below.

 Maintain a firm grip on the power tool and

position your body and arm to allow you to resist

kickback forces. Always use auxiliary handle, if

provided, for maximum control over kickback or

torque reaction during start-up. The operator can

control torque reactions or kickback forces, if proper

precautions are taken.

 Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

 Do not position your body in the area where power

tool will move if kickback occurs. Kickback will

propel the tool in direction opposite to the wheel’s

movement at the point of snagging.

 Use special care when working corners, sharp

edges etc.. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing have

a tendency to snag the rotating accessory and cause

loss of control or kickback.

 Do not attach a saw chain woodcarving blade or

toothed saw blade. Such blades create frequent

kickback and loss of control.

ANGLE GRINDER SAFETY PRECAUTIONS

 Check that the speed marked on the grinding wheel

is equal to or greater than the rated speed of the tool.

 Ensure that the dimensions of the grinding wheel are

compatible with the tool and that the wheel fits the

spindle.

 Grinding wheels must be stored in a dry place.

 Do not store objects on top of the grinding wheels.

 Grinding wheels must not be used for any operation

other than grinding.

 Grinding wheels must be stored and handled with care

in accordance with the manufacturer’s instruction.

 Inspect the grinding wheel before use to ensure that it

is not chipped or cracked. Chips or cracks can cause

the wheels to shatter, resulting in possible serious

injury.

 Ensure that the wheel is fitted in accordance with this

manual.

 Ensure that the grinding wheel is correctly mounted

and tightened before use and run the tool at no-

load speed for 30 seconds in a safe position. Stop

immediately if there is considerable vibration or if other

defects are detected. If this condition occurs, check

the tool to determine the cause.

 Do not use separate reducing bushings or adapters to

adapt large hole grinding wheels.

 Check that the work piece is properly supported.

 Use only recommended accessories.

 Ensure that sparks resulting from use do not create

a hazard, e.g., do not hit people, or ignite flammable

substances.

 Always use protective safety glasses and ear

protectors.

 Use other personal protective equipment such as

gloves, apron and helmet when necessary.

 Never place the tool on the floor or other surfaces

while it is running. Grinding wheels continue to rotate

after the tool is switched off. Never touch the wheel or

place it on the floor or other surfaces while it is rotating.

 The flange and clamp nut must have same outer

diameter.

 Use the tool only for approved applications. Never use

coolants or water or use the tool as a fixed tool.

 Grip the tool securely with both hands while operating.

SPECIFICATIONS

Model EAG750RS EAG750RB

Wheel

diameter

115 mm (4.5 in) 125 mm (5 in)

Thickness 6 mm 6 mm

Voltage

230 V - 240 V

50 Hz

230 V - 240 V

50 Hz

Input 750 W 750 W

Spindle thread M14 M14

Hinnang

Lisateavet selle juhendi kohta

Mõistame, et on tore, kui teil on teie Ryobi EAG750RS Nurklihvija jaoks paberjuhend. Juhendi saate alati meie veebisaidilt alla laadida ja ise printida. Kui soovite originaaljuhendit, soovitame võtta ühendust ettevõttega Ryobi. Nad võivad anda originaaljuhendi. Kas otsite oma Ryobi EAG750RS Nurklihvija kasutusjuhendit mõnes muus keeles? Valige meie kodulehelt oma eelistatud keel ja otsige mudelinumbrit, et näha, kas see on meil saadaval.

Tehnilised andmed

Kõik Ryobi Nurklihvijad kasutusjuhendid
Veel Nurklihvijad käsiraamatuid

Korduma kippuvad küsimused Ryobi EAG750RS Nurklihvija kohta

Meie tugimeeskond otsib kasulikku tooteteavet ja vastuseid korduma kippuvatele küsimustele. Kui leiate meie korduma kippuvates küsimustes ebatäpsusi, andke sellest meile teada, kasutades kontaktivormi.

Seotud tooted

Kasutusjuhend

Ryobi RAG18125-0 Nurklihvija

Kasutusjuhend

Ryobi EAG-8512R Nurklihvija

Kasutusjuhend

Ryobi RAG18115-0 Nurklihvija

Kasutusjuhend

Ryobi EAG750RB Nurklihvija

Kasutusjuhend

Ryobi EAG2000RS Nurklihvija

Kasutusjuhend

Ryobi CAG180M Nurklihvija

Kasutusjuhend

Ryobi RAG18X-0 Nurklihvija

Kasutusjuhend

Ryobi R18AG-0 Nurklihvija

Seotud kategooriad