Kasutusjuhend Wood's WAC703G Milan Silent 7K Kliimaseade

Kasutusjuhend

GB

13

Operating Instructions

A. Accessories

After unpacking, please check whether

the above-mentioned accessories are

included, and check their purposes in

the installation introduction in this

manual.

B. Mobile air conditioner

J. Appearance and Function of Remote

Control.

Notes:- Do not drop the remote control.-

Do not place the remote control in a

location exposed to direct sunlight.

A. Operation Introduction

Before starting operations in this section:

1) Find a place where there is power

supply nearby.

2) Install the exhaust hose, and adjust

the window position well.

3) Connect drain hose well (only for using

heating model);

4) Insert the power cord into an grounded

AC220~240V/50Hz socket;

5) Press the POWER button to turn on

the air-conditioner.

K&L. Introduction to Exhaust Hose

Installation

M) Temporary installation

1.Twist both ends of the exhaust hose

into the Hose Connector.

2.Insert the square xing clip into air

outlet at back of the air conditioner

3.Put the other end of the exhaust hose

to the near windowsill.

N. Window Slider Kit Installation

The installation manner of window slider

kit is mostly in “horizontal” and

“vertical”. As shown Fig.5 and Fig.5a,

check the min. and max. size of the

window before the installation.

1. Install the window kit on the window ;

2. Adjust the length of the window slider

kit according to the window width or

height, and x it with the dowel;

3. Insert the Window connector hose to

the hole of the Window kit.

O. Internal Tank Water Full Alarm

Function

The inner water tank in the airconditioner

has one water level safety

switches, it controls water level. When

water level reaches an anticipated

height, the water full indicator lamp

lights up. Error code “E4” will show on the

display. (If water pump is damaged,

when the water is full, please remove

the rubber blockage at the bottom of

unit, and all water will be drained

outside.)

H. Maintenance Explanations

Declaration:

1) Before cleaning, be sure to

disconnect the unit from any electric

supply outlet;

2) Do not use gasoline or other

chemicals to clean the unit;

3) Do not wash the unit directly;

4) If the conditioner is damaged,

please contact the dealer or repair

shop.

1. Air Filter

-If the air lter becomes clogged with

dust/dirt, the air lter should be

cleaned once every two weeks.

-Dismounting

Open the air inlet grille and take o air

lter.

-Cleaning

Clean the air lter with a neural

detergent in lukewarm ( 40°C ) and let

dry in the shade.

-Mounting

Putting the air lter into the inlet grille,

replace the components as they were.

2. Clean the Air-conditioner Surface

First clean the surface with a neutral

detergent and wet cloth, and then

wipe it with a dry cloth.

E. Before using

Check up whether the exhaust hose

has been mounted properly.

Cautions for cooling and

dehumidifying operations:

-When using functions on cooling and

dehumidifying, keep an interval of at

least 3 minutes between each

POWER.

-Power supply meets the

requirements.

-The socket is for AC use.

-Do not share one socket with other

appliances.

-Power supply is

AC220-240V, 50Hz

1. Turn on the unit

a) Plug in, then the unit beeps once, “ “

The power indicator light is on.

b) Press the “ “ button, then the unit is

turned on.

c) The LED displays the room temperature

and under Automatic mode.

2. Cooling operation

-Press the “Mode” button till the

“Cool” icon appears.

-Press the “+”or“-”button to select

a desired room temperature.

(15°C -31°C )

-Press the “Fan Speed” button to

select wind speed.

3. Dehumidifying operation

Press the “Mode” button till the

“Dehumidify” icon appears .

-Automatically set the selected

temperature to current room

temperature minus 2°C .

-Automatically set the fan motor to

LOW wind speed.

4. Fan operation

-Press the “Mode” button till the “Fan”

icon appears.

-Press the “Fan Speed” button to

select wind speed.

5. Heating operation (this function is

not available for a cold-single unit)

-Press the “Mode” button till the

“Heat” icon appears.

a desired room temperature.

FUNCTION OF THE OPERATION MODES AND INSTALLATION DESCRIPTIONS

It is very important that the lter is

cleaned regularly; otherwise the

air conditioner might lose capacity

and even be seriously damaged.

Hinnang

Lisateavet selle juhendi kohta

Mõistame, et on tore, kui teil on teie Wood's WAC703G Milan Silent 7K Kliimaseade jaoks paberjuhend. Juhendi saate alati meie veebisaidilt alla laadida ja ise printida. Kui soovite originaaljuhendit, soovitame võtta ühendust ettevõttega Woods. Nad võivad anda originaaljuhendi. Kas otsite oma Wood's WAC703G Milan Silent 7K Kliimaseade kasutusjuhendit mõnes muus keeles? Valige meie kodulehelt oma eelistatud keel ja otsige mudelinumbrit, et näha, kas see on meil saadaval.

Tehnilised andmed

Kõik Wood's Kliimaseadmed kasutusjuhendid
Veel Kliimaseadmed käsiraamatuid

Korduma kippuvad küsimused Wood's WAC703G Milan Silent 7K Kliimaseade kohta

Meie tugimeeskond otsib kasulikku tooteteavet ja vastuseid korduma kippuvatele küsimustele. Kui leiate meie korduma kippuvates küsimustes ebatäpsusi, andke sellest meile teada, kasutades kontaktivormi.

Seotud tooted

Kasutusjuhend

Wood's WAC9G Torino Kliimaseade

Kasutusjuhend

Wood's WAC901G Capri Silent 9K Kliimaseade

Kasutusjuhend

Wood's WAC7G Roma Kliimaseade

Kasutusjuhend

Wood's WAC1801G Venezia Silver 18K Kliimaseade

Kasutusjuhend

Wood's WAC1210G Como 12K Kliimaseade

Kasutusjuhend

Wood's WAC18G Venezia 18K Kliimaseade

Kasutusjuhend

Wood's WAC903G Milan Silent 9K Kliimaseade

Kasutusjuhend

Wood's WAC1802G Venezia 18K Smart Home Kliimaseade

Seotud kategooriad